Best ProPress Tools for Copper Pipe (2026): Cordless and Manual
The pick: RIDGID RP 351, and who should buy something else
Buy the RIDGID RP 351 in kit 67183 for copper ProPress work from 1/2 to 1 inch that an inspector or a client will look at. RIDGID rates it at 7,200 lbs (32kN) of ram output with no scheduled maintenance.
Get RIDGID RP 351These picks were not tested. They come from what the makers’ documents show. Each pick is chosen on four things its maker documents for that exact kit: copper ProPress-profile jaws for the sizes in the box, how the tool is driven, what ships in the case, and the maker’s own force, run-time and service figures. One more test decides the top pick: whether Viega’s tool matrix (TD-TL 0326) lists the tool. The RIDGID RP 351 is on it. The iCrimp and VEVOR tools are not, and their verdicts below say so.
- Top pick, 1/2 to 1 inch, or to 2 inch with kit 67178: RIDGID RP 351. Kit 67183 includes jaws for 1/2 to 1 inch, an 18V 2.5Ah battery, a charger and a case.
- Compact cordless for tight bays, up to 1-1/4 inch: Milwaukee M12 FORCE LOGIC kit 2573-22. Milwaukee approves the M12 for copper press fittings up to 1-1/4 inch with CTS-V jaws. The kit includes 1/2, 3/4 and 1 inch jaws, and Milwaukee states service every 37,000 press cycles.
- A few 1/2 to 1 inch joints, and you already own an impact wrench: iCrimp IWS-1632CF. It is driven by a socket wrench or an impact wrench and comes with three jaws and a tubing cutter. iCrimp’s store lists it at $166.99.
- A few joints, no impact wrench, and you want a cutter and deburrer in the box: VEVOR hydraulic copper pipe crimping tool (model AL-1632). It is hydraulic-driven, with a 360° head. VEVOR’s store lists it at $102.90.
- Battery power on a budget: the VEVOR 24KN press tool (MP-2430) for 1/2 to 1 inch at up to 200 crimps per charge, or the VEVOR 32KN press tool (ZEP-1550) for 1/2 to 2 inch at up to 350 crimps per charge.
Not worth the money: the VEVOR 32KN press tool or RIDGID kit 67178 for work that never goes past 1 inch. Both include 1-1/4, 1-1/2 and 2 inch jaws that a 1/2 and 3/4 inch repipe never uses.
RIDGID RP 351 against the Milwaukee M18 FORCE LOGIC
RIDGID’s RP 351 and Milwaukee’s M18 FORCE LOGIC are both 18V cordless press tools, and their force ratings tie. RIDGID’s page for the RP 351 gives 7,200 lbs (32kN) of ram output. Milwaukee’s operator’s manual 58-14-0167 gives the M18 FORCE LOGIC 2922-20 a nominal force of 7,200 lbs, says only trained personnel should operate it, gives an operating temperature of 14°F to 122°F, and calls for at least 15 minutes of cool-down after 30 minutes of continuous use. Viega’s matrix lists both. It pairs RIDGID RP 330, 340, 350 and 351 tools with RIDGID Standard jaws for ProPress 1/2 to 2 inch. It pairs the Milwaukee M18 Force Logic with M18 jaws for 1/2 to 2 inch, and with M18 rings for 2-1/2 to 4 inch.
For most buyers the RP 351 wins on how RIDGID packages and services it:
- Kit choice. Kit 67183 ships with jaws for 1/2 to 1 inch only, so a remodeler or service plumber whose copper stops at 1 inch does not pay for 1-1/4 to 2 inch jaws. Milwaukee’s copper kit, the 2922-22, comes with CTS jaws from 1/2 to 2 inch, plus two M18 batteries, a charger and a case.
- Service. RIDGID states no scheduled maintenance and a brushless motor capable of over 100,000 press cycles.
- Features. RIDGID lists an endless 360° head swivel, Bluetooth connectivity, color-coded light indicators, and a capacity of 1/2 to 4 inch on copper and stainless steel.
The M18 wins in two cases. A shop already running M18 batteries avoids buying into a second battery platform. A contractor managing several tools gets Milwaukee’s ONE-KEY remote tracking, management and lockout, which goes beyond what RIDGID claims for its Bluetooth link. RIDGID gives the RP 351 as 7.0 lbs (3.2 kg) and 15.6 inches long; its operator’s manual gives 7.83 lbs (3.55 kg) with no battery or attachment. Milwaukee’s dealers are listed under Where To Buy on the 2922-22 page.
Who should not buy the RP 351:
- Anyone pressing a handful of joints once. A tool rated for over 100,000 cycles is more than that job needs.
- Anyone whose batteries are already M18 or M12.
Kit 67178, with jaws to 2 inch, is worth it only when 1-1/4 to 2 inch mains or hydronic headers are on the job list.
Milwaukee M12 FORCE LOGIC for joist bays and boiler rooms
The Milwaukee M12 FORCE LOGIC kit 2573-22 is the cordless pick for copper inside joist bays, behind boilers and in vanity cabinets, where a Standard-class tool can’t swing. It is chosen on Milwaukee’s own approval and figures. Milwaukee’s 2026 press tool compatibility matrix approves the M12 for copper press fittings up to 1-1/4 inch with CTS-V jaws and rings for M12. Milwaukee’s page for the 2573-22 lists what is in the box:
- the 2573-20 press tool
- a 1/2 inch jaw (49-16-2450), a 3/4 inch jaw (49-16-2451) and a 1 inch jaw
- two M12 REDLITHIUM 2.0 batteries (48-11-2420)
- a charger and a case
Milwaukee’s press release announced the kit at $2,449.
Milwaukee covers it with a 5-year tool warranty, a 2-year battery warranty and a 2-year jaw warranty. Its pages for the 2573 tool state service every 37,000 press cycles. Auto-Cycle runs each press to completion, and an indicator light shows when a full cycle was reached or when the tool needs calibration. The same tool takes other jaw sets. Milwaukee sells it as the 2573-22M with 3/8, 3/4 and 7/8 inch Streamline ACR jaws, and as the 2573-22Z with ZoomLock MAX and >B< MaxiPro jaws. That matters to an HVAC tech who presses refrigerant fittings as well as hydronic copper, because one tool body covers both.
Two limits rule it out for some buyers:
- Pipe size. Milwaukee’s matrix approves the M12 only up to 1-1/4 inch on copper, so a 1-1/2 or 2 inch header needs the RP 351 or the M18.
- Jaws. Jaws that look alike are not interchangeable. The RIDGID Compact jaws in the M12 column of Milwaukee’s matrix are listed for PureFlow, which is Viega’s PEX system, not copper ProPress. Milwaukee’s matrix also says not to use Milwaukee press tools with any jaw or ring it has not approved.
For a single repair, the M12 kit costs far more than the job is worth. Take a manual tool below, or hire the joint out.
Manual and budget cordless: iCrimp against VEVOR
Viega’s tool matrix lists hand tools only for PureFlow PEX, none for ProPress, and no iCrimp or VEVOR tool. Viega’s ProPress installation manual says its products ‘are designed to be installed by licensed and trained plumbing and mechanical professionals who are familiar with Viega products and their installation.’ The four tools below are for a homeowner or remodeler pressing a few 1/2 to 1 inch joints where that listing is not the deciding point. They are chosen on jaw sizes, drive, box contents and each maker’s published figures. Where a job will be inspected, or you want a tool on Viega’s list, buy the RP 351. Viega says it does not require specific, approved tools to maintain its fitting warranty.
iCrimp IWS-1632CF: the manual pick if you own an impact wrench. iCrimp’s page for the IWS-1632CF describes it as driven by a socket wrench or an impact wrench. The kit holds the press tool, jaws for 1/2, 3/4 and 1 inch ProPress fittings, a tubing cutter and a socket wrench. The impact wrench is not included, and iCrimp says the kit is not for PEX or refrigerant fittings. iCrimp says to confirm exact compatibility and settings in the product instructions, and to allow room for head, socket and drive movement. iCrimp’s store lists it at $166.99. Its lever-handle sibling, the IWS-1632AF, lists at $140.99. It has double extendable handles and a 360-degree rotating head but no wrench drive, so you close every joint by arm. iCrimp says it is not for PEX or HVAC refrigerant fittings and to allow full handle opening. For 1-1/4 and 1-1/2 inch copper, iCrimp’s store lists the IWS-2538CF, which covers 1, 1-1/4 and 1-1/2 inch, at $179.99. iCrimp says it is not a PEX or refrigerant RLS/ZoomLock kit, and that its LED is a completion indicator, not a leak detector.
VEVOR AL-1632 hydraulic tool: the pick if you have no impact wrench and want the prep tools in the box. VEVOR’s page for the AL-1632 lists three interchangeable jaws for 1/2, 3/4 and 1 inch copper and a 360° rotating head for narrow spaces. The box also holds a copper pipe cutter, a deburring tool and a carrying case. Between the two manual tools, VEVOR wins on box contents, and iCrimp wins for anyone with an impact wrench.
VEVOR 24KN (MP-2430): the cheapest battery tool here. VEVOR rates it at 24 kN on 18V. VEVOR states up to 200 crimps per charge. The kit holds two 2.0Ah batteries, a fast charger, a case and three VUS jaws for 1/2 to 1 inch. VEVOR says a 1-1/4 inch jaw set is sold separately, and that the tool takes only 24KN compact jaws. VEVOR’s store lists it at $589.90.
VEVOR 32KN (ZEP-1550): the RP 351’s force rating on paper. VEVOR rates it at 32 kN on 18V, the same figure as RIDGID’s 32kN. The kit holds six VUS jaws from 1/2 to 2 inch and two 4.0Ah batteries, and VEVOR states up to 350 crimps per charge. VEVOR recommends maintenance after about 20,000 uses but does not require it. VEVOR’s store lists it at $1,044.90. Compared with RIDGID kit 67178, it gives you two 4.0Ah packs where RIDGID’s battery kit has one 2.5Ah battery. In exchange you give up Viega’s listing and RIDGID’s no-scheduled-maintenance rating.
Jaw series: what fits which tool
A jaw has to match on three counts: the fitting profile, the size, and the tool series. If any one is wrong, you can end up with a jaw that seats in the tool, looks right and is not approved.
- Profile. Copper ProPress fittings take a V-profile jaw. Milwaukee calls its copper jaws CTS-V, and VEVOR calls its copper jaws VUS. Milwaukee’s IPS-P jaws, such as the 1 inch 49-16-2452B for the M12, are for iron-pipe-size fittings, not copper tube.
- Size. A tool kit’s range is the range of the jaws in the box, not of the tool body. RIDGID rates the RP 351 for 1/2 to 4 inch copper, but kit 67183 presses only 1/2 to 1 inch until you add jaws. Viega’s matrix covers 2-1/2 to 4 inch on the Milwaukee M18 Force Logic only with M18 rings.
- Series. Viega’s matrix lists Standard jaws for 1/2 to 2 inch ProPress on RIDGID RP 330, 340, 350 and 351 tools and on the Viega Pressgun 6. It lists Compact jaws for 1/2 to 1-1/4 inch on the Viega Pressgun Picco 6. VEVOR draws the same line by force rating: the MP-2430 takes only 24KN compact jaws, while VEVOR says the ZEP-1550 works with any standard 32KN-rated jaw.
- Brand approval. Milwaukee’s matrix approves CTS-V jaws for copper on its M12 and M18 tools and warns against using any jaw or ring it has not approved. VEVOR’s listing for its 3/4 inch VUS jaw claims a fit on RIDGID RP 240, RP 241 and RP 251 compact tools and on the Milwaukee M12. Milwaukee’s matrix does not list VEVOR jaws, and that claim comes from VEVOR alone.
A jaw is approved for a tool when the tool maker’s matrix or the fitting maker’s matrix names that pairing. A jaw that physically locks into the tool proves nothing. Buy the tool and its jaws as one documented pairing, and add sizes from the same maker’s jaw line: CTS-V for a Milwaukee tool, RIDGID Standard jaws for an RP 351, VUS 24KN jaws for an MP-2430.
Run-time, service intervals and the pressure test
What each maker publishes on run-time, service and access:
- RIDGID RP 351: no scheduled maintenance, a brushless motor capable of over 100,000 press cycles, an endless 360° head swivel, color-coded light indicators and Bluetooth. RIDGID gives an operating temperature range of 15°F to 122°F (-10°C to 50°C); the tool will not operate outside it.
- Milwaukee M12 FORCE LOGIC 2573: service every 37,000 press cycles, Auto-Cycle to complete each press, a light that signals a full cycle or a calibration need, and a 5-year tool warranty. Milwaukee’s operator’s manual says only trained personnel should operate the tool and to keep hands away from the press jaw while it is in use, gives an operating temperature of 14°F to 140°F, and calls for at least 15 minutes of cool-down after 30 minutes of continuous use.
- VEVOR 24KN (MP-2430): up to 200 crimps per charge on two 2.0Ah packs.
- VEVOR 32KN (ZEP-1550): up to 350 crimps per charge on two 4.0Ah packs, with maintenance recommended after about 20,000 uses.
- Manual tools: no charge limit. The iCrimp IWS-1632AF and the VEVOR AL-1632 both have 360° rotating heads.
Service intervals separate the tiers more than crimps per charge do. A homeowner doing one repipe will not reach VEVOR’s 20,000-use maintenance suggestion or Milwaukee’s 37,000-cycle service. A contractor pressing daily will, and that is where RIDGID’s no-scheduled-maintenance rating and Milwaukee’s calibration light earn their cost. A tool that tells you a press did not finish is a check most of the manual and budget tools don’t document; iCrimp’s IWS-2538CF has an LED completion indicator, which iCrimp says is not a leak detector.
No tool replaces the pressure test. Viega’s ProPress installation manual describes its Smart Connect feature: an unpressed connection shows up during pressure testing when water or air flows past the sealing element. Pressure-test every system before closing walls, whichever tool made the joints. That test is how you catch a joint a hand tool was released from too early, or a fitting that was never pressed. RIDGID’s RP 350/RP 351 manual adds that any time the pressure release button is used the press connection is not complete and must be pressed again, to keep fingers and hands away from the attachment during the press cycle because they can be crushed, fractured or amputated, and not to use the tool while standing in water.
Where ProPress copper belongs in HVAC work, and the size line
Viega lists ProPress copper fittings with EPDM sealing elements for 0°F to 250°F and 300 psi, in sizes 1/2 to 4 inch. That covers hydronic heating loops, near-boiler piping, chilled-water lines and domestic water. It leaves refrigerant lines out. Refrigerant press connections use their own fitting systems and jaws, such as the Streamline ACR, ZoomLock MAX and >B< MaxiPro fittings that Milwaukee’s 2573-22M and 2573-22Z kits press. A ProPress copper jaw on a refrigerant fitting is the wrong pairing at any size.
Prep decides as much as the tool. Viega’s ProPress installation manual says to cut the tube square, deburr it inside and out, and mark the insertion depth before the fitting goes on. The VEVOR AL-1632 kit includes both a cutter and a deburring tool. The iCrimp IWS-1632CF kit includes a tubing cutter only, so add a deburring tool.
Match the tool to your largest pipe:
- 1 inch and smaller: every pick on this list except the iCrimp IWS-2538CF (1, 1-1/4 and 1-1/2 inch jaws only) covers it. The RP 351 in kit 67183 is the one Viega lists.
- 1-1/4 inch: the Milwaukee M12 FORCE LOGIC (Milwaukee approves it up to 1-1/4 inch), the VEVOR MP-2430 with VEVOR’s separately sold 1-1/4 inch set, or iCrimp’s IWS-2538CF.
- 1-1/2 to 2 inch: the RP 351 in kit 67178, the Milwaukee 2922-22, or the VEVOR ZEP-1550.
- 2-1/2 to 4 inch: a Standard-class tool with rings, such as the Milwaukee M18 Force Logic with the M18 rings that Viega lists for that range.
If a future job might reach 1-1/2 inch, buy the tool that covers it now. A compact tool approved only to 1-1/4 inch cannot be extended to larger sizes, and Viega’s matrix gives 1/2 to 1-1/4 inch as the ProPress range for Compact jaws.
Related guides
- AC and mini split coil-cleaning supplies: mini split cleaning kits and wash bags, no-rinse and foaming evaporator/condenser coil cleaners, fin combs, and soft brushes (by unit type: wall-mounted mini split indoor head, outdoor condenser, window AC)
- AC and mini split condensate management: condensate pumps, drain-line clog prevention and overflow protection
- Best Air Purifiers for Allergies (2026)
- Best Basement Dehumidifiers
FAQ
Can a manual press tool make Viega ProPress joints?
iCrimp and VEVOR both sell manual tools with ProPress-profile jaws for 1/2 to 1 inch copper, such as the iCrimp IWS-1632CF and the VEVOR AL-1632. Viega’s tool matrix lists hand tools only for PureFlow PEX, none for ProPress, and no iCrimp or VEVOR tool. For work that will be inspected, or where Viega’s listing matters, use a listed tool such as the RIDGID RP 351 with RIDGID Standard jaws. Whichever tool you use, pressure-test the system: Viega’s Smart Connect feature makes an unpressed fitting show up during the test.
Do RIDGID jaws work on a Milwaukee M12 or M18 press tool?
For copper, Milwaukee’s 2026 matrix approves CTS-V jaws and rings on its own tools: up to 1-1/4 inch on the M12, and up to 2 inch with jaws and to 4 inch with rings on the M18 FORCE LOGIC. The RIDGID Compact jaws in the matrix’s M12 column are listed for PureFlow PEX, not copper ProPress. Milwaukee’s matrix says not to use Milwaukee press tools with any jaw or ring it has not approved.
Is a 1/2 to 1 inch kit enough, or should I buy jaws to 2 inch?
If your largest copper is 1 inch, a 1/2 to 1 inch kit such as RIDGID 67183, Milwaukee 2573-22 or VEVOR MP-2430 covers it, and a 2 inch kit adds three jaw sizes you won’t use. For 1-1/4 inch, Milwaukee approves the M12 up to that size, and VEVOR sells a 1-1/4 inch set for the MP-2430. For 1-1/2 to 2 inch headers, buy RIDGID kit 67178, Milwaukee 2922-22 or the VEVOR ZEP-1550.