How to Install a Mini Split DIY: The Best DIY Mini Splits to Buy, Then the Step-by-Step Install
The mini split to buy for a DIY install is the MRCOOL DIY 5th Gen 12K 115V (bundle DIY-12-HP-WM-115D25-O). It was picked on three criteria. First, the maker backs a homeowner install: MRCOOL’s DIY 5th Gen warranty is 5 years on parts and 7 years on the compressor “with no registration required”, and needs no contractor unless the law or a MRCOOL-directed diagnosis calls for one. Second, the refrigerant stays sealed: a 25 ft Quick Connect line set arrives pre-charged with R-454B, so there is no vacuum pump and no refrigerant charging, though MRCOOL still says to wear goggles and work gloves when connecting it. Third, it runs on 115V: one dedicated 20 A circuit. These picks were not tested; the figures are MRCOOL’s own.
Get MRCOOL DIY 5th Gen 12K 115VThe best DIY mini splits at a glance
| Pick | Best for | MRCOOL’s figures | Circuit (max breaker) |
|---|---|---|---|
| MRCOOL DIY 5th Gen 12K 115V | One room, most homes | 23.5 SEER2, up to 550 sq ft | 115V, 20 A |
| MRCOOL DIY 5th Gen 24K 230V | One large or open room | 22.7 SEER2, up to 1,050 sq ft | 208/230V, 25 A |
| MRCOOL DIY 5th Gen Hyper Heat 12K 230V | Cold winters | Runs from -22°F to 122°F | 208/230V, 15 A |
| MRCOOL DIY 5th Gen 3-Zone 18K Condenser | Two or three rooms | 23.9 SEER2, up to 750 sq ft | 208/230V, 20 A |
All four carry the same DIY 5th Gen warranty: 5 years parts, 7 years compressor, no registration. No CPSC recall lists any MRCOOL mini split. The one CPSC recall naming Mr. Cool covers Midea-made U and U+ window air conditioners, not these units.
1. Best overall: MRCOOL DIY 5th Gen 12K 115V
This is the one to buy if you are cooling and heating a single bedroom, office, garage or living room and want to do the work yourself. MRCOOL rates the 12K at 12,000 BTU/h cooling and heating, 23.5 SEER2, 12.5 EER2 and 10.2 HSPF2 (Region IV), for rooms up to 550 sq ft. It is ENERGY STAR certified, and MRCOOL’s manual lists outdoor operation from -13°F to 122°F in cooling and -13°F to 75°F in heating.
Get MRCOOL DIY 5th Gen 12K 115VWhat makes it the DIY pick is the line set. MRCOOL describes the Quick Connect set as pre-charged with R-454B and not requiring vacuuming; you thread the fittings onto the air handler and the condenser and open the valves with an Allen key. The 115V version also avoids a 240V run: MRCOOL lists a minimum circuit ampacity of 18 A and a maximum breaker of 20 A, and the manual recommends 12 AWG wire.
A complete system is two boxes, the condenser (DIY-12-HP-C-115D25-O) and the air handler (DIY-12-HP-WMAH-115D25-O). Some listings sell them separately, so make sure the listing you buy includes both, plus the line set.
Who should buy something else: anyone heating through winters that regularly drop below -13°F (see the Hyper Heat below), anyone with a room over 550 sq ft, and anyone who wants the cheapest box regardless of warranty.
2. Best for a large room: MRCOOL DIY 5th Gen 24K 230V
For an open main floor, a finished basement or a two-car garage, the 24K (DIY-24-HP-WM-230D25-O) is MRCOOL’s step up. MRCOOL rates it at 24,000 BTU/h, 22.7 SEER2, 12.7 EER2 and 9.5 HSPF2, for up to 1,050 sq ft. It needs a 208/230V circuit: 24 A minimum circuit ampacity, 25 A maximum breaker, and 10 AWG wire per the manual.
Get MRCOOL DIY 5th Gen 24K 230VIt wins on capacity per circuit, and the manual allows up to 75 ft of line set and 75 ft of height difference between indoor and outdoor unit, against 49.2 ft of height for the 12K. It is a heavier job: the condenser weighs 122.8 lb net, the line set is 3/8 in by 5/8 in with adapters, and the manual lists wrenches up to 1-1/4 in. Plan on two people.
3. Best for cold winters: MRCOOL DIY 5th Gen Hyper Heat 12K 230V
If your winters go below the standard unit’s -13°F floor, buy the Hyper Heat. MRCOOL lists its operating range as -22°F to 122°F, with 23.5 SEER2, 12.8 EER2 and 10 HSPF2 (Region IV), for up to 550 sq ft. It pairs the DIYHH-12-HP-C-230D25-O condenser with the 230V wall air handler (DIY-12-HP-WMAH-230D25-O) and carries the same DIY 5th Gen warranty, which lists that condenser by model number.
Get MRCOOL DIY 5th Gen Hyper Heat 12K 230VThe trade-off is the circuit. The Hyper Heat runs on 208/230V, not 115V; MRCOOL lists a 15 A minimum circuit ampacity and a 15 A maximum breaker. If you only have room for a 115V circuit and your winters stay above -13°F, the 12K 115V is the better buy.
4. Best for two or three rooms: MRCOOL DIY 5th Gen 3-Zone 18K Condenser
MRCOOL is the only one of these makers that sells a multi-zone system for homeowner install. The DIY-MULTI3-18HP230D-O condenser runs two or three wall or ceiling-cassette heads, rated by MRCOOL at 18,000 BTU/h, 23.9 SEER2 and 10 HSPF2 for up to 750 sq ft combined. It needs 208/230V: 16 A minimum circuit ampacity, 20 A maximum breaker.
Get MRCOOL DIY 5th Gen 3-Zone 18K CondenserBuy it only if you are ready for a bigger job. Each head needs its own line set, wall hole, drain and DIYPRO cable, and the multi-zone manual sets limits you have to plan around: 75 ft maximum per indoor unit, 24 ft maximum height difference between indoor units, 33 ft maximum length difference between indoor and outdoor unit, and a 9.8 ft minimum run per head to limit vibration and noise. MRCOOL’s figures for total line set disagree: the multi-zone manual lists 172 ft for all rooms on a three-zone, while MRCOOL’s product FAQ gives 123 ft for the 18K three-zone, so plan to the lower figure. The heads and line sets are sold separately or in bundles; match head sizes to MRCOOL’s published match-ups for this condenser. Check room size for every head too: the 3-zone condenser alone holds 61.73 oz of R-454B, just under the 62.7 oz point where the multi-zone manual’s minimum room area jumps from 12 sq ft to roughly 57-60 sq ft or more, each line set adds charge, and MRCOOL lists this condenser as not a limited-releasable-charge system.
If 25 feet is not enough: MRCOOL DIY 35 ft Pre-Charged Line Set
The 12K ships with a 25 ft set (MRCOOL’s manual gives the standard length as 24.6 ft). If the condenser has to sit farther away, MRCOOL sells the same pre-charged Quick Connect set in 35 ft and 50 ft lengths. For the 9K and 12K (1/4 in by 3/8 in) the 35 ft set is DIY35-1438C-O, pre-charged with R-454B; the 50 ft is DIY50-1438C-O. The manual’s limit for the 9K and 12K is 75 ft of line set, so either fits inside it. Order the length you need rather than coiling extra: excess line set has to be coiled flat behind the condenser.
Get MRCOOL DIY 35 ft Pre-Charged Line SetWhat is not worth the money
MRCOOL sells two other DIY lines on the same pre-charged idea, and both give up warranty.
- MRCOOL DIY Select (DIYS models): 1 year on parts and 2 years on the compressor, a shorter 11.5 ft line set, and SEER2 ratings up to 17.5. The 5th Gen’s 5 and 7 years is the better buy for a system you install once.
- MRCOOL DIY Easy Pro (EZPRO models ending in DE): 3 years on parts and 5 years on the compressor, and its warranty defines parts as everything except the compressor or line sets, so the pre-charged line set is not covered as a part.
Not DIY at all, by their makers’ own terms:
- Senville states that pressure testing and evacuation of line sets “must be completed by a licensed HVAC professional” and that “DIY installation will void your warranty coverage.”
- Pioneer’s warranty is a Basic Warranty of up to one year unless you register within one week after the product is properly installed, which earns the Standard Warranty of up to five years. It excludes faulty installation and moisture or air let into the system during installation, and claims start with a diagnosis by the installer or a qualified contractor.
What MRCOOL’s DIY warranty actually says
Read these terms before you buy, because they decide whether a self-install stays covered.
- Length: 5 years parts, 7 years compressor, from the proof-of-purchase date, with no registration required.
- Condition: it applies only to systems installed according to the installation instructions and in accordance with all applicable local, state and federal laws, “including but not limited to electrical codes and permits.”
- When a contractor comes in: “When required by law or when required for diagnostic testing as directed by MRCOOL, a State or province certified or licensed HVAC contractor may be necessary.”
- Line set: the manual states the warranty applies only if the line set is installed as described, that the line sets are designed to be installed only once, and that disconnecting and reconnecting them can leak and voids the warranty. Refrigerant loss from dirt or moisture in the connectors is not covered.
- Not covered: labor, refrigerant and its cost, faulty installation, units moved from the original address, and units installed outside the USA and Canada.
- Lifetime replacement: only through MRCOOL’s optional paid care program (the warranty calls it the MRCOOL Care Kit Program): while you stay enrolled, a failed compressor is replaced, and a failure within the first 7 years gets a full outdoor unit.
Where you need a licensed electrician, and other limits in MRCOOL’s manual
MRCOOL’s product page calls the DIY “designed for full homeowner installation” with “no license, no technicians.” Its installation manual is stricter, and its warnings are given here at their own strength:
- The manual opens with a warning in capitals that installation must be performed by an authorized dealer or specialist and that electrical work must be completed by a qualified electrical technician.
- Its wiring section says all wiring must comply with local and national electrical codes and “must be installed by a licensed electrician.” The multi-zone manual says the same.
- The unit needs its own circuit: do not share the power supply with other appliances. Fixed wiring must include an all-pole disconnect with at least 3 mm (1/8 in) contact separation and a residual current device rated at no more than 30 mA, and the unit must be grounded.
- After switching the power off, wait at least 10 minutes before touching electrical components.
- The unit is not intended for use by people (including children) with reduced physical, sensory or mental capabilities, or lacking experience and knowledge, unless supervised or instructed by a person responsible for their safety; children must be supervised so they do not play with it.
- Anyone who works on or breaks into a refrigerant circuit should hold a current certificate for handling refrigerants. The DIY install never opens the circuit; any later refrigerant repair is technician work.
The practical reading: you can do the mounting, the wall hole, the line set and the drain, and MRCOOL’s warranty does not need a contractor for them. The circuit, breaker, disconnect and power connection go to a licensed electrician, as MRCOOL’s manual says; your building department decides who may pull the electrical permit.
Room-size limits for R-454B
R-454B is mildly flammable, so the manual sets placement rules. The indoor unit must sit at least 6.0 ft above the floor, in a room at least 7.3 ft high. The minimum room area depends on the system charge: the 12K (30.34 oz) needs 12 sq ft, while the 24K (67.37 oz) needs about 67 sq ft at a 6 to 7.3 ft mounting height. Each pre-charged line set also holds refrigerant (2.12 oz in a 25 ft set, 4.66 oz in a 35 ft 3/8 x 5/8 set), and the table goes by actual system charge, so with a longer set check the table against your total; above 70.5 oz the 24K needs 73 sq ft. The 5th Gen has a refrigerant leak sensor; on a leak the indoor unit shows an error code and beeps, the compressor stops, and the indoor fan runs. The sensor must stay powered except during service.
How to choose a DIY mini split
Size it to the room. A common starting point is about 20 BTU per square foot, then adjust up for tall ceilings, poor insulation or big sunny windows. MRCOOL’s own maximum coverage figures are 550 sq ft for the 12K and 1,050 sq ft for the 24K. Our mini split BTU sizing calculator does the adjustment.
Pick the voltage your panel can supply. The 9K and 12K come in 115V; 18K and up are 208/230V. Ask the electrician which one your panel has room for before you order.
Measure the line set run. Measure from the indoor unit’s piping exit, through the wall, along the house to the condenser’s valves. The 12K’s 25 ft set covers most runs to an outside wall; past that, buy a longer pre-charged set rather than cutting or splicing; MRCOOL designs its line sets to be installed only once.
Check the climate. For heating below -13°F, the Hyper Heat’s -22°F rating is the reason to buy it. Our best heat pump by climate zone guide covers which climates need it.
If you are still choosing between brands, see our best mini split AC systems roundup and the Mr. Cool vs Senville vs Pioneer comparison.
How to install a DIY mini split, step by step
These steps follow MRCOOL’s DIY 5th Gen single-zone manual for the wall-mounted 9K-36K. The Hyper Heat condenser is not on that manual’s model list and the multi-zone has its own manual; the instructions that ship with your unit govern if anything differs.
Tools and materials
- Stud finder, level and tape measure
- Core drill or hole saw, 3.54 in (90 mm), plus masonry bits for brick or concrete
- Two adjustable wrenches (the manual lists 3/4 in to 1 in for the 12K and 18K, up to 1-1/4 in for the 24K and 36K)
- A 5 mm Allen key (included) and a Phillips screwdriver
- An HVAC torque wrench, if available (a socket-style wrench cannot be used)
- Leak-detection spray or soapy water and a brush
- Goggles and work gloves
- Condenser pad or wall bracket, drain hose extension, line set cover (optional)
- Electrical: disconnect, breaker, wire and whip, installed by the electrician
For the hardware that ships separately, see our best mini split installation kits.
Step 1: Choose the locations
Indoor: at least 6.0 ft above the floor, with at least 5.9 in to the ceiling and 4.72 in at each side, at least 3.28 ft from TVs and other electronics, and not near a heat source, a doorway, curtains or direct sun. The piping exits on the right as you face the unit.
Outdoor: a firm, level spot with good airflow, away from combustible gas, heavy dust or salty air, and sheltered from heavy rain or snow without blocking airflow. If you hang it on a wall bracket, the wall must be solid brick, concrete or similar and able to carry at least four times the unit’s weight. For a garage, see our best mini split for garage picks.
Step 2: Mount the plate and drill the wall hole
Screw the mounting plate flat and level to the wall, into studs where you can. Drill the 3.54 in hole so the indoor end sits about 0.2 to 0.275 in higher than the outdoor end, so condensate drains outward. Avoid wires and plumbing. Insert the wall sleeve and trim it flush outside.
Step 3: Hang the indoor unit
Bend the piping out from the back of the unit slowly, without denting it. Tape the pipes and drain hose into a bundle with the drain at the bottom, leaving the connectors bare. Feed the DIYPRO cable and the bundle through the hole, hook the top of the unit on the plate, and press the bottom until it snaps on. A second person helps here.
Step 4: Set the outdoor unit
Install the drain joint if your condenser needs one, then bolt the unit level on its pad or bracket with M10 bolts. In cold climates, run the drain hose as vertically as possible so meltwater does not freeze in it.
Step 5: Connect the pre-charged line set
On the 24K, first check that the adapters on the condenser valves are tight, as the manual directs. Unwind only as much line as you need, keeping a 4 in minimum bend radius. Do not bend the same section more than three times or past 90 degrees. Connect in dry weather only, and keep the caps on until the moment you connect. Never run the unit without the line set connected; MRCOOL says it will be damaged immediately. Do not smoke during the installation. Thread each fitting on by hand, hold the nut marked “1” with one wrench and turn the nut marked “2” with the other until snug, then torque by the stamp on the connector:
| Stamp | Coupling size | Torque |
|---|---|---|
| FA06 | 3/8 in | 18-20 lb-ft |
| FA09 | 1/2 in | 30-35 lb-ft |
| FA12 | 3/4 in | 45-50 lb-ft |
| FA16 | 1 in | 60-65 lb-ft |
Without a torque wrench, the manual says to go slightly past snug and not overtighten. No thread tape or sealant: the fittings seal by compression and sealant can make them leak. Coil any excess flat behind the condenser.
Step 6: Open the valves and check for leaks
MRCOOL’s line set page also says to perform a leak test before opening the valves. Remove the valve caps with a 19 mm wrench, open each valve counter-clockwise with the 5 mm Allen key as far as it goes without forcing it, and refit the caps tight. Brush soapy water or leak spray on all four connections; bubbles mean a leak, so tighten and check again. Wrap the joints with the supplied insulation and UV tape, drain hose at the bottom. Do not plaster over the line set or hide it inside a wall; MRCOOL advises against both.
Step 7: Electrical (licensed electrician)
The electrician runs the dedicated circuit, breaker and disconnect, and connects power and the DIYPRO cable at the condenser: its numbered wires go to the matching terminals, ground to the bottom screw.
Step 8: Test run
Do not turn on the power until the installation and all work has been completed. Run it for at least 30 minutes: cool at the lowest set point and heat at the highest, five minutes each, then recheck all four connections for leaks, since pressure rises during operation. When the ambient temperature is below 60°F, the remote will not start cooling; use the manual control button (press twice for cool). Pour a little water across the coil to confirm the drain flows.
Common DIY installation mistakes
- Wall hole sloped the wrong way. Water runs back into the wall. The outdoor end must be lower.
- Drain hose on top of the bundle, kinked or trapped. MRCOOL warns this can overflow the drain pan.
- Over- or under-tightened fittings. Too loose leaks; too tight damages the connector. Use the torque table.
- Reconnecting a line set. The fittings are made to seal once; undoing them can leak and voids the warranty.
- Thread tape on Quick Connect fittings. It can cause a slow leak.
- Sharing the circuit. The manual forbids other appliances on the unit’s circuit.
- Too much bending. More than three bends in one spot, or past 90 degrees, can crack the copper.
When to call a pro instead
- The electrical work. MRCOOL’s manual puts all wiring with a licensed electrician; a full or outdated panel adds a panel job on top.
- A flare-connection system. Any brand without a pre-charged line set needs pressure testing and evacuation of the line set, which Senville requires a licensed HVAC professional to do.
- Any refrigerant repair. Breaking into the circuit is certified-technician work under the manual’s own warnings. The manual also puts any unit repair, and any maintenance and cleaning of the outdoor unit, with an authorized dealer or licensed service provider.
- Your local rules require it. MRCOOL’s warranty itself says a licensed contractor may be necessary when required by law, so check with your building department before you buy.
FAQ
Does a DIY install void the mini split warranty?
It depends on the maker. MRCOOL’s DIY 5th Gen keeps its 5-year parts and 7-year compressor warranty for a homeowner install that follows the instructions, codes and permits, with no registration. Senville states DIY installation voids its warranty. Pioneer’s runs one year unless registered within a week of a proper install.
Do I need an EPA certification to install a pre-charged mini split?
A pre-charged Quick Connect install never opens the refrigerant circuit. MRCOOL’s manual says anyone who works on or breaks into a refrigerant circuit should hold a current refrigerant-handling certificate, so any later repair is technician work.
Do I need a permit?
Ask your building department before you start; a new circuit commonly needs one. MRCOOL’s warranty applies only to systems installed in line with electrical codes and permits, so the permit protects the warranty as well.
Can I install a mini split in winter?
You can mount everything in cold weather, but connect the line set outdoors only in dry weather. For the test run below 60°F, start cooling with the manual control button. The standard DIY 5th Gen heats down to -13°F outdoors; the Hyper Heat to -22°F.
How long does a DIY mini split install take?
Plan a full day for a single-zone wall unit with a helper, plus the electrician’s visit. A multi-zone takes longer because every head needs its own hole, line set and cable.
What size mini split do I need?
Start near 20 BTU per square foot and adjust for ceilings, insulation and sun. MRCOOL rates the 12K for up to 550 sq ft and the 24K for up to 1,050 sq ft. Use our mini split BTU sizing calculator.
Related Articles
- Best Mini Split AC Systems — Find the right unit before you install
- Best Mini Split Installation Kits — Tools and accessories for a clean install
- Mini Split Sizing Calculator — Get the right BTU for your space
- Mr. Cool vs Senville vs Pioneer — Compare DIY-friendly brands
- Best HVAC Tools for Beginners — Essential tools for the job